305230_0116_ROC_1Gal_Wolman_DuraStain_OutdoorFurniture

Wolman

™

DuraStain

Outdoor Furniture is an exceptional water-base wood coating designed to refresh your exterior wood furniture, picnic

tables, playsets, and more. DuraStain

Outdoor Furniture is 4x thicker for enhanced durability and provides ultimate weather resistance in even

the harshest weather conditions. It decorates wood furniture with deeply pigmented, bright color that provides solid hide.

READ ALL INSTRUCTIONS BEFORE BEGINNING

TINT BASE: MUST BE TINTED BEFORE USE / FOR EXTERIOR USE ONLY

WOLMAN

DURASTAIN® OUTDOOR FURNITURE can be applied using a 3/8” or ½” nap roller or a synthetic paint brush.

DIRECTIONS FOR USE

WHERE TO USE

FOR EXTERIOR, ABOVE GROUND USE ONLY.

WOOD TYPES: Use on all species of Pine, Fir, Hemfir, Cypress, Cedar, Redwood, Poplar, Hickory, and other North

American hardwoods.

PROJECTS: Use to beautify and protect wood furniture, picnic tables, playsets, and more.

COVERAGE: Approximately 80 square feet per gallon (volume after tinting). Two coats are recommended. Actual

coverage will vary depending on wood age and species, and surface porosity.

APPLICATION INSTRUCTIONS

SURFACE PREPARATION: The preparation process outlined below should be followed to achieve optimum performance

of this product. Long-term adhesion and durability can be impaired by an unsound or poorly prepared surface.

REGARDLESS OF AGE OR SURFACE CONDITION, FAILURE TO FOLLOW THESE PREPARATION METHODS MAY RESULT IN

POOR ADHESION AND POSSIBLE COATING FAILURE. NEW AND SEALED WOOD NEEDS TO WEATHER AT LEAST SIX MONTHS

BEFORE APPLICATION.

Step 1: Prepare the surface with Wolman

™

DeckStrip

, then use DeckBrite™ or Deck & Fence Brightener based on your wood condition

described below. After preparation, conduct Splash Test (see Step 2) on bare wood to confirm water absorption before applying this product.

Previously Coated, Weathered Wood: 1) For best results, previous coatings such as paints, solid color and semi-transparent stains in a

weathered state should be stripped to create a bare, sound surface for maximum coating adhesion and durability. To remove oil, alkyd or latex,

water base stains, use Wolman

™

DeckStrip

Stain & Finish Remover; for 100% acrylic solid or semi-solid stains, use DeckStrip

-ASR Acrylic

Stain Remover. 2) For previous coatings in a sound condition, and for weathered transparent finishes, toners and clear sealers, thoroughly

clean with Wolman

DeckBrite

powder concentrate or Deck & Fence Brightener liquid concentrate to remove chalky paint residue,

embedded dirt, mildew and other contaminants, residual coating material and water repellency. According to label guidelines, select the

appropriate cleaning product for your wood type, use according to directions and rinse with a power washer for best results. When dry, scrape

off and sand any remaining loose flaking or peeling coating using 50 or 60 grit sandpaper.

Uncoated, Weathered Wood: Before staining, bare, weathered wood must be thoroughly cleaned to remove ground-in dirt, mildew, mold and

algae stains, gray, UV-damaged wood fibers and any other surface contaminants. According to label guidelines, select the appropriate product

for your particular wood type, either Wolman

DeckBrite

powder concentrate or Deck & Fence Brightener liquid concentrate. Follow usage

directions on label, let dry, then conduct Splash Test (see Step 2).

Uncoated, New Wood: It is important to open wood pores and remove any surface barrier which would prevent the proper penetration or

adhesion of a new coating. If pressure-treated lumber, excess surface wax or excessive internal moisture content may be present. If new

Cedar or Redwood, “mill glaze” on the surface is a common condition. Eliminate these barriers by using either Wolman

™

DeckBrite

™

powder

concentrate or Deck & Fence Brightener liquid concentrate. According to label guidelines, select the appropriate product for your particular

wood type, then follow usage directions on label, let dry, and conduct Splash Test (see Step 2).

Step 2: Perform a Splash Test: To conduct a Splash Test, sprinkle several handfuls of water on a few distinct areas of the bare wood surface.

If the water absorbs rapidly, the surface is ready to be coated. If the water beads, puddles or is not absorbed, an internal or external barrier

exists, and must be eliminated before staining can begin.

Houses painted before 1978 may contain lead. WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC.

EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a

wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at

1-800-424-LEAD or log on to www.epa.gov/lead.

TINTING: DuraStain

Outdoor Furniture should be tinted before use with compatible universal colorants.

BEFORE YOU START COATING: Prior to project start date, perform a trial brush-out in several inconspicuous areas to ensure the desired color

and look is achieved. (Color appearance will vary depending wood species, age and surface porosity). Secure raised nail heads and remove

loose splinters. Fill cracks with an acrylic, non-silicone filler. Allow to dry. This product will not repair existing wood damage such as cracking,

checking, splintering or splitting. Make sure entire wood surface is completely dry and free of dust, dirt and debris. Cover all surrounding areas

not intended to be coated. Intermix multiple gallons of the same product in a separate container to ensure a uniform color. Mix thoroughly

before and occasionally during use. Do not dilute or mix this product with any other product.

PRECAUTIONS & TEMPERATURE SAFEGUARDS:

DO NOT APPLY IF RAIN IS EXPECTED WITHIN 24 HOURS OF APPLICATION. Apply when surface and air temperature is between 50º and 90º F

and will remain between 50º and 90º F for at least 2 hours after application.

APPLICATION

TWO LIBERAL COATS OF WOLMAN

™

DURASTAIN

OUTDOOR FURNTITURE ARE REQUIRED.

STEP 1: Thoroughly stir material before and during project. When using more than one container, combine all containers to ensure color

consistency.

STEP 2: Using either a 3/8” or ½” nap roller or a synthetic paint brush, saturate and apply generously in a consistent pattern. Work to a wet

edge at all times. Avoid rolling back into coated areas where drying has begun.

STEP 3: If needed, use a putty knife or other straight edge to remove excess coating between boards.

STEP 4: Allow first coat to dry 4-6 hours. Extend drying time if the surface is tacky or soft. Drying times may vary depending on temperature and humidity.

STEP 5: Apply second coat using the same method as in STEP 2 and STEP 3.

STEP 6: Allow second coat to dry 24 hours before light use and 3-5 days for heavy use. Full cure to a hard finish will take approximately 3-4 weeks.

Clean up drips or spatters with water IMMEDIATELY, as dried coating is very difficult to remove.

CLEAN UP: Use mild soap and water as soon as possible.

STORAGE: KEEP FROM FREEZING. Close container when not in use. Dispose of empty cans or unused portion in accordance with local, state

and federal regulations.

MAINTENANCE: It is recommended to periodically clean using Wolman

Deck Wash or a mild, non-abrasive soap and water mixture to

keep coating grime-free and looking its best.

WARNING: Causes eye, skin and respiratory irritation. Avoid contact with eyes and skin and use

adequate ventilation. If swallowed, call poison control center, hospital emergency room, or

physician immediately. When tinted, contains ethylene glycol which can cause severe kidney

damage when ingested and has been shown to cause birth defects in laboratory animals and also

diethylene glycol which may cause central nervous system effects and liver or kidney damage.

WARNING: This product contains chemicals known to the state of California to cause cancer and

birth defects or other reproductive harm.

FIRST AID

EYE CONTACT: Immediately flush eyes with plenty of cool water for at least 15 minutes. Seek

medical attention.

SKIN CONTACT: Wash thoroughly with soap and water. If irritation persists, seek medical attention.

INHALATION: If you experience difficulty in breathing, leave the area to obtain fresh air. If continued

difficulty is experienced, get medical attention.

INGESTION: If swallowed, contact a physician or poison control center. Do not induce vomiting

unless directed to do so by a physician. Never give anything by mouth to an unconscious person.

LIMITED WARRANTY

Rust-Oleum Corporation guarantees product performance for the product in this can only when

applied according to the label directions. You will receive as your exclusive remedy either a refund

of the original purchase price or replacement with a product of equal value. We do not guarantee

the product against factors beyond our control, such as damage to the product by others, poor

condition of the substrate, structural defects, improper application, etc.

This warranty does not apply to use of the Product in combination with other materials.

Warranty is made to the original residential product purchaser and is not transferable.

If not satisfied with the product, Rust-Oleum will, at its option upon proof of purchase, either furnish

an equivalent amount of new product or refund the purchase price. In no event shall seller or

manufacturer be liable to user, buyer, or any third party for consequential or incidental damages or

losses resulting from the use of the Product. The terms of this Warranty Disclaimer and Limitation of

Liability cannot be varied by any written or verbal statements or agreements. No employee or sales

agent is authorized to vary the terms of the Warranty Disclaimer and Limitation of Liability.

Rust-Oleum will not be responsible for labor or cost of labor for the removal or application of any

product, or replacement of any wood structure. To obtain a warranty remedy, write to Rust-Oleum

Corp., 11 E Hawthorn Pkwy, Vernon Hills, IL 60061, and include proof of purchase.

The Company, seller, and manufacturer make no other warranties, guarantees, or representations

of any kind to buyer or user, or to any third party, either express or implied or by usage of trade,

statutory or otherwise, with regard to the Product, including, but not limited to warranties of

merchantability, fitness for a particular purpose, or use or eligibility of the goods for any particular

trade usage. No warranties shall be created by course of performance, usage of trade, or course

of dealing.

KEEP OUT OF REACH OF CHILDREN

VOC: Product contains less than 50 grams per liter

FURNITURE

WARNING:

IRRITANT

Read carefully other cautions on back panel.

3 Quarts 20 FL OZ. (116 FL OZ.) | 3.43 LITERS

X THICKER FOR

ENHANCED DURABILITY

WATERPROOFING

PROTECTION

EXTENDS LIFE OF

WOOD FURNITURE

ULTIMATE

WEATHER RESISTANCE

WATER BASE

IDEAL FOR: WOOD PLAYSETS, PICNIC TABLES, OUTDOOR FUNITURE, & MORE

COVERS 80 SQ FT WITH TWO COATS

tint base

neutral

COATING

OUTDOOR

1-800-901-0411

rustoleum.com/wolman

Made in USA

Hecho en E.U.A.

306089LBL GAL

0116

305230 TINT BASE

.5625" inch Glue Flap